Key takeaways
- Compare seven waterproof sprays for horse blankets, with sizes, application steps and drying times, so you can pick the right treatment for a turnout shell.
A turnout blanket that wets out in rain needs a water repellent finish on its outer shell, because the factory coating wears off with use and washing. best waterproof spray for horse blankets compares seven sprays with maker stated sizes, application steps and drying times, so you can pick the right treatment for a turnout shell.
Quick verdict on the best waterproof spray for horse blankets
For most readers, the Nikwax TX.Direct Spray-On is the top pick here, because it restores water repellency on breathable turnout shells without heat, and the maker states a 300 ml bottle with a simple spray and wipe method. The Scotchgard Heavy Duty Water Shield is the quick aerosol pick, with a short 2 to 6 hour drying time.
The seven picks split into two groups. Four are water based DWR sprays made for breathable waterproof fabrics, while three are silicone or fluoropolymer sprays made for heavier canvas and mixed gear. Readers with a modern breathable turnout shell should start with the Nikwax, Gear Aid and Grangers picks, and readers with an older canvas style shell should compare the Star brite, Atsko and Kiwi picks first.
A spray restores water repellency on the outer shell only. It does not repair a torn blanket, fix a failed seam, or replace a waterproof membrane that has broken down, so a blanket that leaks through the lining needs repair or replacement, not another coat of spray. Read the maker label for each product before use, and let the treated blanket dry fully before it goes back on the horse.
Comparison table for waterproof sprays for turnout shells
Use this table to compare the seven picks side by side before reading the full notes below. Focus first on application and drying time, then on size and the fabrics each maker lists, because those facts decide how much planning a treatment needs and whether the spray suits your blanket shell.
| Product | Best for | Size | Application | Drying time | Works on |
|---|---|---|---|---|---|
| Nikwax TX.Direct Spray-On | Breathable turnout shells with wicking liners | 300 ml | Spray 15 cm away on clean wet fabric, wipe surplus after 2 min | Air dry; DWR develops as it dries | Gore-Tex, eVent, Sympatex, all waterproof breathable fabrics |
| Scotchgard Heavy Duty Water Shield | Quick aerosol treatment for nylon and polyester shells | 10.5 oz | Spray 6 to 8 in sweeping motion on clean dry fabric | 2 to 6 hours | Polyester, nylon, cotton, leather, suede |
| Star brite Waterproofing Spray | Large canvas and heavy turnout shells | 22 oz | Spray, brush or sponge to wet top surface; fabric must be dry | 6 hours | Nylon, canvas, cotton, polyester, acrylic |
| Atsko Silicone Water-Guard | Long lasting silicone coat for mixed gear | 10.5 oz | Spray evenly on clean dry material | 24 hours; full cure 72 hours | Tents, boots, leather, suede, breathable membranes |
| Kiwi Camp Dry Heavy Duty Water Repellent | Silicone treatment for canvas and leather trim | 10.5 oz | Spray 6 to 8 in even passes; second coat after 4 hours | 2 to 6 hours; full cure 24 to 48 hours | Tents, tarps, boots, canvas, leather, fabric |
| Gear Aid ReviveX Durable Water Repellent Spray | Technical shells that need heat to set the finish | 10 oz | Spray 5 to 10 in on clean dry garment | Machine dry medium heat or air dry 24 hours | Nylon, Gore-Tex, eVent, NeoShell |
| Grangers Performance Repel Plus | PFC free spray for damp shells after washing | 275 ml | Spray evenly on freshly cleaned damp garment, wipe excess | Not stated | Gore-Tex, eVent, waterproof breathable fabrics, soft shell, fleece |
How we selected these sprays
Every pick in this guide is a real waterproofing spray from a named maker, with a published size and published application steps, and each one suits the outer shell of a turnout blanket. Where a maker publishes a drying time, the table states it, and where a maker does not, the table states that plainly.
This guide compares sprays only, which sets it apart from the earlier turnout blanket roundups in this project that compared the blankets themselves. Those guides covered shell denier, fill weight and fit, while this guide covers the treatment that goes on the shell, so the two groups answer different questions and should not be read as the same kind of roundup.
Selection also weighed fabric match and drying time. A DWR spray suits a modern breathable shell, a silicone spray suits a heavy canvas shell, and a fluoropolymer spray suits mixed fabrics with leather trim. Drying times run from 2 hours to 3 days, so readers should pick a spray whose drying time fits the gap before the blanket is needed again.
Seven waterproof sprays for turnout blankets
The seven picks below run from a water based DWR spray made for breathable shells to a silicone spray made for heavy canvas, so readers can see how chemistry, application and drying time change together. Read the application steps first, then the drying time and the fabrics each maker lists.
Nikwax TX.Direct Spray-On
The Nikwax TX.Direct Spray-On is the top pick in this guide, because it restores water repellency on breathable waterproof shells without heat, and the maker states a 300 ml bottle. The spray on method suits blankets with wicking liners that should not be machine washed, since only the outer face gets treated.
The wet fabric method is the main reason to choose this spray. The maker states that the blanket should be cleaned first with Nikwax Tech Wash, then sprayed while still wet from about 15 cm away, with any surplus wiped off with a damp cloth after 2 minutes. The DWR finish develops as the fabric air dries, so no tumble drying is needed, which protects older shells from heat.
The trade off is coverage, because the maker states that one 300 ml bottle treats only 1 to 2 garments, so a large turnout blanket may need most of a bottle for one full treatment. The maker also states larger 500 ml and 1 liter sizes, so readers who treat several blankets should compare the bigger bottle before buying the small one.
Scotchgard Heavy Duty Water Shield
The Scotchgard Heavy Duty Water Shield is the quick aerosol pick in this guide, with a 10.5 oz can and a maker stated drying time of 2 to 6 hours. The maker states that one can covers about 60 square feet on light nylon or 20 square feet on heavier fabrics, which suits a single turnout shell.
The fast drying time is the main reason to choose this spray. The maker states a simple three step method: spray in a sweeping motion 6 to 8 inches away to cover the fabric evenly, let it dry for 2 to 6 hours, and apply a second coat after the first has dried for extra protection. The maker also states that the finish dries odorless and does not block fabric breathability.
The trade off is the aerosol format, because the maker warns that the contents are flammable and under pressure, so readers must apply it outdoors or in a well ventilated area away from heat and flame. The maker lists polyester, nylon, cotton, leather and suede among the fabrics it suits, which covers most turnout shell and trim combinations.
Star brite Waterproofing Spray
The Star brite Waterproofing Spray is the large shell pick in this guide, with a 22 oz spray bottle and a 1 gallon size for readers who treat several blankets. The maker states that the formula restores water repellency to marine fabrics, and it adds UV protection and stain repellency to the treated surface.
The size range is the main reason to choose this spray. The maker states that the 22 oz bottle covers about 80 square feet and the 1 gallon size covers about 465 square feet, so one bottle treats a full turnout shell with room left over. The maker states that the fabric must be dry before application, and the spray can be applied with the included sprayer, a brush or a sponge.
The trade off is the drying time, because the maker states that the treated item must dry for 6 hours before use, and must not be folded or stored until dry. The maker lists nylon, canvas, cotton, polyester and acrylic among the fabrics it suits, so it fits heavy canvas style turnout shells best, and readers should apply it outdoors in a well ventilated area.
Atsko Silicone Water-Guard
The Atsko Silicone Water-Guard is the long lasting silicone pick in this guide, with a 10.5 oz aerosol can and a 1 gallon size. The maker describes it as an all purpose waterproofing spray, and the silicone formula keeps fabric breathable while it adds water repellency to the surface.
The single coat method is the main reason to choose this spray. The maker states that it should be applied to clean dry material and left until fully cured before use, with a drying time of 24 hours and a full cure in 72 hours. That long cure suits readers who can treat a blanket at the start of a dry spell and leave it hanging for three days before it goes back on the horse.
The trade off is the curing time and a color warning, because the maker states that the spray can yellow white or light colored materials, so readers should spot test a hidden area first and wait 24 hours before treating the whole shell. The maker lists tents, boots, leather and suede among its uses, and it is also recommended for breathable membranes.
Kiwi Camp Dry Heavy Duty Water Repellent
The Kiwi Camp Dry Heavy Duty Water Repellent is the silicone canvas pick in this guide, with a 10.5 oz aerosol can. The maker describes it as a heavy duty silicone water repellent for boots, tarps, tents and rain gear, and the silicone base suits canvas shells that need a thick water shedding coat.
The two coat method is the main reason to choose this spray. The maker states that the can should be held 6 to 8 inches from the fabric for even passes, with a drying time of 2 to 6 hours, and a second coat applied after 4 hours when maximum protection is needed. One 10.5 oz can covers a full tent fly in two coats, so a single turnout shell fits within one can.
The trade off is the cure time, because several sources state that full curing takes 24 to 48 hours, so readers should not pack the blanket away or put it on the horse until the surface is fully dry. The maker lists tents, tarps, boots, canvas, leather and fabric among its uses, and the spray is approved for use on cotton canvas, which suits older turnout shells.
Gear Aid ReviveX Durable Water Repellent Spray
The Gear Aid ReviveX Durable Water Repellent Spray is the heat set pick in this guide, with a 10 oz non aerosol pump bottle, also sold in 5 oz and 16.9 oz sizes. The maker states that it restores the DWR coating on waterproof breathable outerwear, including Gore-Tex jackets, ski pants, gloves and nylon tent flies.
The heat activation is the main reason to choose this spray. The maker states that the clean dry garment should be sprayed from 5 to 10 inches away in a well ventilated area, with extra spray on high wear areas like shoulders and cuffs, then machine dried on medium heat or air dried for 24 hours. That heat step sets the finish firmly on technical shells that see hard use.
The trade off is the small bottle, because the maker states sizes of 5, 10 and 16.9 oz, and a large turnout blanket may need the biggest bottle for full coverage. The maker lists nylon, Gore-Tex, eVent and NeoShell among the fabrics it suits, so it fits modern breathable turnout shells with a membrane best, and readers should check the blanket care label before machine drying.
Grangers Performance Repel Plus
The Grangers Performance Repel Plus is the PFC free pick in this guide, with a 275 ml spray bottle, also sold in a 500 ml size. The maker states that it restores the durable water repellent finish on technical outerwear, and it is Bluesign approved with no heat activation needed for the finish to work.
The damp fabric method is the main reason to choose this spray. The maker states that it should be sprayed evenly onto a freshly cleaned damp garment, with any excess removed with a clean cloth, then allowed to dry naturally. That method suits readers who wash the blanket first and want to treat it while it is still damp from the wash, without a separate drying step.
The trade off is the drying time, because the maker states only that the garment should be allowed to dry completely before use, with no fixed number of hours published, so readers should plan for an overnight dry. The maker lists Gore-Tex, eVent, waterproof breathable fabrics, soft shell and fleece among the fabrics it suits, which covers most modern turnout shells.
Buying guide for turnout blanket reproofing
A good choice starts with the shell fabric, then the application method and the drying time. The fabric decides which chemistry suits the blanket, the method decides wet or dry application, and the drying time decides how far ahead the treatment must be planned. Work through the three in order and the right spray is usually clear.
Match the best waterproof spray for horse blankets to your shell
A modern breathable turnout shell suits a DWR spray, because Nikwax, Gear Aid and Grangers list Gore-Tex among the fabrics they treat, and those sprays restore repellency without blocking breathability. The Nikwax pick suits lined shells, the Gear Aid pick suits heat safe shells, and the Grangers pick suits shells still damp from washing.
A heavy canvas shell suits a silicone or fluoropolymer spray, because Star brite, Atsko and Kiwi list canvas, nylon and mixed fabrics among their uses, and those formulas build a thicker water shedding coat. The Star brite pick suits large shells, the Atsko pick suits mixed gear with leather trim, and the Kiwi pick suits cotton canvas shells that need two coats.
Plan the drying time before you spray
Drying times in this guide run from 2 hours to 3 days, so the gap before the blanket is needed again decides the pick. The Scotchgard and Kiwi picks dry in 2 to 6 hours, the Star brite pick needs 6 hours, and the Nikwax pick dries as the fabric air dries with no fixed time stated by the maker.
The Atsko and Gear Aid picks need the most planning, because Atsko needs 24 hours to dry and 72 hours to cure fully, while Gear Aid needs machine drying on medium heat or 24 hours of air drying. The Grangers pick states no fixed drying time, so readers should allow an overnight dry and test the surface before the blanket goes back on the horse.
Treat seams, straps and high wear areas
Seams and straps leak first, because stitching holes and folded edges give water a path through the shell even when flat panels still bead. The Nikwax maker states its spray suits targeted treatment of seams and wear areas, and the Gear Aid maker states extra spray should go on shoulders and cuffs, the same wear spots on a turnout blanket.
A second coat on the wear spots is worth the extra product, because the Scotchgard and Kiwi makers both state that a second coat adds protection after the first has dried. Readers should spray the seams, the chest straps and the tail flap first, let those areas dry, then treat the flat panels, so the weakest spots get the most coverage.
Frequently asked questions
These questions cover the points that readers ask most often when they shop for a spray to reproof a horse blanket. The answers focus on what a spray can and cannot do, how often to reapply, and how to apply it safely, because those three facts decide whether the treatment holds through a wet season.
Can a spray make a turnout blanket fully waterproof again
No, a spray restores water repellency on the outer shell, which means rain beads and rolls off instead of soaking into the face fabric, but it does not rebuild a waterproof membrane or seal a torn seam. A blanket with a failed membrane will still let water through the lining after the outer face beads, so that blanket needs repair or replacement.
A spray works best on a blanket whose shell is sound and whose coating has simply worn off with use and washing. Readers should test the blanket by spraying water on the outer face: if the water beads, the finish is still working, and if it soaks in and darkens the fabric, the shell is ready for a fresh coat of spray.
How often should a horse blanket be resprayed
Respray when the outer face stops beading water, which usually happens after a season of hard use or after the blanket has been washed several times. The makers in this guide do not publish a fixed number of months between treatments, so the water bead test is the honest guide, not a calendar date.
A blanket that lives outdoors in rain will need treatment sooner than one that spends most of its time in a dry stable. Readers should check the shell at the start of the wet season and again halfway through, and treat the blanket on a dry day with enough time left for the full drying period before the horse needs it again.
Can I spray a blanket while the horse is wearing it
No, never spray a blanket while the horse is wearing it. Every maker in this guide states that sprays should be applied outdoors or in a well ventilated area, away from heat and flame, and the fumes and overspray are not safe for the horse to breathe or for its skin and eyes.
Remove the blanket, clean it, lay it flat or hang it in a ventilated space, and spray the outer face only. Let the treated blanket dry fully for the time the maker states before it goes back on the horse, and keep the horse away from the drying area until the surface is dry and the smell has gone.
Conclusion
The Nikwax TX.Direct Spray-On is the top pick for most readers, with a simple wet fabric method and no heat needed for the finish to develop. The Scotchgard pick suits readers who want the fastest drying time, the Star brite pick suits large canvas shells, and the Atsko and Kiwi picks suit readers who want a long lasting silicone coat.
Write Your Review
No reviews yet. Be the first to share your experience!