Updated Nov 17, 2026· 15 min read

Key takeaways

  • Find the best washers for coin operated laundromats, from 20 lb front loaders to 35 lb extraction models, with capacity, spin, water use, and control details.

A laundromat lives or dies on washers that start on the first coin and hold up under constant use. The best washers for coin operated laundromats pair a solid drum and a strong final spin with controls an owner can set and service without fuss. This guide compares seven models by capacity, spin, water use, and payment.

Quick verdict

Seven commercial washers made the cut, from a 20 lb entry front loader to a 35 lb high extraction model. The table below lines up capacity, extraction, and the main trade off for each machine, so an owner can shortlist by floor space and load mix before reading the full notes on each model.

Product Type Best for Key spec Main limit
Speed Queen FV6 FV6000WN Front load, coin drop Small stores and shared rooms 21 lb capacity, 440 G spin Only 3 wash cycles
Maytag Commercial MAT24PDAXW Top load, dual coin drop Owners who want a familiar top loader 3.3 cu ft basket, 1/2 HP motor Single basket size only
Dexter T-300 C-Series Front load hardmount Small stores starting a row 20 lb capacity, 100 G spin, 1 HP Needs a concrete base and bolting
Dexter T-400 C-Series Front load hardmount Mid size family loads 30 lb capacity, 100 G spin, 2 HP Heavy at 433 lb net weight
Wascomat WED730-CV Front load solid mount Busy stores that want high extraction 30 lb capacity, 200 G spin, 776 RPM Needs a concrete foundation
LG Titan C Washer Coin Front load, coin Large family loads 35 lb capacity, 327 G spin, 980 RPM Wider 29 in cabinet takes more floor space
Huebsch Vended Front Load Washer Front load, coin slide Small stores wanting a 440 G spin 21.5 lb capacity, 440 G spin, 1200 RPM Only 3 wash cycles

For a small store, the shortlist starts with the two 440 G front loaders, the Speed Queen FV6 and the Huebsch vended front loader, plus the Dexter T-300 for owners who want a hardmount row they can grow. Stores that see more family loads and bedding should look at the 30 lb Dexter T-400 and Wascomat WED730-CV, the 35 lb LG Titan C, or the top load Maytag MAT24PDAXW.

How we selected

Selection started with published maker specification sheets and listing product pages, not with sales claims. Each model below had a page we could open and read, with a stated capacity, a stated spin or extraction figure, and a coin payment option, so every number in this guide traces back to a page the owner can also open.

Capacity, extraction force, water use per cycle, electrical service, and control options carried the most weight, because those five factors decide how many loads a store turns, how long drying takes, and how much utility work an install needs. Where a page did not state a fact, this guide says so instead of filling the gap.

Washers for coin operated laundromats

Each washer below fits a coin operated laundromat, but the seven models split into clear groups: compact 20 lb front loaders, a top loader, mid size 30 lb hardmount machines, and a 35 lb high extraction front loader. Read the notes with the floor plan and the load mix in mind, since the right pick depends on both.

Speed Queen FV6 FV6000WN front load washer

The FV6 suits a small laundromat or a shared laundry room that needs a compact coin drop front loader with a strong final spin. Its 21 lb capacity covers everyday family loads, while the 440 G extraction leaves clothes drier at the end of the wash, which shortens the dryer run that follows.

The maker lists a 3.42 cu ft stainless steel cylinder, a 1200 RPM spin, a 0.9 HP motor, and water use of 13.68 gal per cycle. Three cycles are offered, Normal, Synthetic, and Delicate, with three water temperatures, Cold, Warm, and Hot. Electrical service is 120 volt, 60 Hz, single phase, 15 amp, and the cabinet measures 26.875 in wide, 43.875 in high, and 31.36 in deep, with a net weight of 260 lb. The maker describes balancing technology that redistributes unbalanced loads, the front control model is listed as ADA compliant, and the coin box is listed as a required kit sold separately.

What stands out:

  • 440 G extraction at 1200 RPM
  • Standard 120 volt 15 amp supply
  • Stainless steel cylinder in a 26.875 in cabinet

What to watch:

  • Only three wash cycles
  • Coin box is sold separately

Buy it if the store is small and most customers bring everyday family loads. Skip it if the store needs a bigger drum for bedding.

Maytag Commercial MAT24PDAXW top load washer

The MAT24PDAXW suits owners who want a familiar top load layout with factory installed coin payment. Its deep water wash and flex vane agitator give customers a traditional wash feel, while Intelligent Controls let the owner set cycle pricing from the panel.

The maker lists a 3.3 cu ft capacity, with a 3.27 cu ft wash basket, and a 1/2 HP PSC motor driving a quad gear transmission. The PowerWash cycle delivers more agitation, hotter water, and an extra rinse for tough loads, and the flex vane agitator alternates between four distinct wash patterns. A dual coin drop is factory installed, and the maker lists a 5 year limited parts warranty.

Intelligent Controls with M-Series technology offer individual cycle pricing options, a display that shows prices, selections, and time remaining, and built in diagnostics. A USB port supports firmware updates without special equipment, plus export of diagnostic and audit data. The wash shaft is 100 percent 416 grade stainless steel, and a triple lip seal with garter spring protects the shaft and bearings.

What stands out:

  • Factory installed dual coin drop
  • PowerWash cycle with an extra rinse for heavy soil
  • USB port for firmware updates and audit data export

What to watch:

  • The maker does not state water use per cycle
  • Only one basket size

Buy it if customers prefer top loaders and the owner wants simple coin payment with audit data. Skip it if the store plan centers on front loaders.

Dexter T-300 C-Series washer

The T-300 is the entry hardmount front loader in the Dexter C-Series line, built for a small store that wants a 20 lb coin machine with room to grow. Its 100 G extraction and 1 HP motor cover everyday loads, and the C-Series control works with coin acceptors or a payment system.

The maker lists a dry weight capacity of 20 lb, a cylinder volume of 2.7 cu ft, and a high extract speed of 100 G at 579 RPM, with a wash speed of 0.9 G at 55 RPM. Approximate water use is 15.8 gal per cycle, the motor is 1 HP, and the net weight is 317 lb. The cabinet is 43 7/8 in high, 26 in wide, and 25 in deep, with a door opening of 12 1/4 in.

The sheet lists a 10 year limited warranty covering the frame, tub, cylinder, shaft, seals, bearings, and bearing housing, plus a 3 year parts warranty. The maker states that every model is designed to withstand a 1,000 hour out of balance test, and that the washer fits through a standard 36 in doorway. Minimum concrete thickness is listed at 6 in, and C-Series controls work with DexterLive for remote programming.

What stands out:

  • 10 year limited warranty on core parts
  • Ships with coin acceptors or payment system ready
  • DexterLive remote programming

What to watch:

  • Hardmount build needs a concrete base and bolting
  • 100 G extraction trails the higher spin models

Buy it if the store is new or small and the owner wants a hardmount row that can grow. Skip it if most customers bring family size loads.

Dexter T-400 C-Series washer

The T-400 moves the same C-Series build up to a 30 lb dry weight capacity, which suits family loads and small bulk items that crowd a 20 lb drum. Its 4 cu ft cylinder and 15 1/4 in door opening make loading bedding and towels easier than in the smaller model.

The maker lists a dry weight capacity of 30 lb, a cylinder volume of 4 cu ft, and a high extract speed of 100 G at 532 RPM, with a wash speed of 0.9 G at 50 RPM. The motor is 2 HP, the net weight is 433 lb, and the cabinet is 48 3/16 in high, 29 7/8 in wide, and 27 3/8 in deep. The cylinder is 25 in in diameter, the door opening is 15 1/4 in, water flow is listed at 9 gal per minute, and the drain diameter is 3 in. Minimum concrete thickness is 6 in, and the C-Series line is listed with the same 10 year limited warranty on core parts and the option of coin acceptors or payment system ready.

What stands out:

  • 30 lb capacity with a 4 cu ft cylinder
  • Wide 15 1/4 in door opening
  • 2 HP motor for the larger drum

What to watch:

  • 433 lb net weight needs care in delivery
  • Hardmount build needs a concrete base and bolting

Buy it if the store needs a mid size hardmount washer for family loads. Skip it if the floor cannot take a hardmount install.

Wascomat WED730-CV coin washer

The WED730-CV suits a busy store that wants a 30 lb washer with a much stronger final spin than the 100 G hardmount models. Its 200 G extraction at 776 RPM pulls more water from each load, which can shorten dryer time and raise the number of turns a store handles each day.

The maker lists a capacity of 30 lb, a cylinder volume of 4.6 cu ft, and an extract speed of 776 RPM at 200 G. The cabinet is 28 3/8 in wide, 48 1/16 in high, and 31 1/8 in deep, with a door opening diameter of 14 3/8 in. Power is listed at 0.5 kW with a 15 amp circuit breaker, on 208 to 240 volt single phase or 120 volt single phase.

Water use is listed at 40.7 gal total on a full load warm cycle, with 3/4 in inlet fittings, a flow of 5 gal per minute per inlet at 44 psi, and recommended water pressure of 30 to 90 psi. The drain outlet diameter is 3 in, the modified energy factor is 2.2, and noise in extraction is listed at under 72 dBA. The front panel is offered in white or stainless steel, and the sheet states that solid mount machines need a concrete foundation and are not for upper floors.

What stands out:

  • 200 G extraction at 776 RPM
  • 4.6 cu ft cylinder
  • Dual voltage options

What to watch:

  • Solid mount needs a concrete foundation
  • 40.7 gal water on a full load warm cycle is the highest figure here

Buy it if the store turns many loads a day and a stronger spin will cut dryer queues. Skip it if the floor is not a concrete slab.

LG Titan C Washer Coin front load washer

The Titan C washer suits a store that serves large family loads and wants a quiet, high spin machine in a 29 in cabinet. Its 35 lb capacity is the largest single load washer in this guide, and its 327 G extraction leaves loads drier than the 100 G models.

The maker lists a capacity of 35 lb, a drum volume of 5.2 cu ft, an extract speed of 980 RPM at 327 G, and a wash speed of 46 RPM. Water use is 17.8 gal per cycle, the default program duration is 35 minutes, and noise is listed at lower than 62 dB. Dimensions are 29 in wide, 40.8 in high, and 32 in deep, with electric ratings of 120 volt, 60 Hz, 5 amp.

The drum is attached directly to the motor through Inverter Direct Drive, with no belt and pulley, and the maker describes fewer parts than a belt drive. The tub is tilted at 10 degrees, the drain is a gravity drain, and four friction dampers absorb vibration. The steel control panel, stainless steel drum, tempered glass door, and top mounted dispenser are all listed on the maker page, with coin, card, and on premise versions offered.

What stands out:

  • Largest capacity here at 35 lb
  • 327 G extraction at 980 RPM
  • Noise listed at lower than 62 dB

What to watch:

  • 29 in width and 32 in depth take more floor space
  • Listed as a non heater model

Buy it if the store serves large loads and wants the biggest drum with a strong, quiet spin. Skip it if floor space is tight.

Huebsch Vended Front Load Washer

The Huebsch vended front loader suits a small store that wants the strongest spin in a compact cabinet. Its 21.5 lb capacity and 440 G extraction match the Speed Queen FV6 on paper, while the MDC control adds a coin countdown and a time remaining display for customers.

The maker lists a capacity of 21.5 lb, a cylinder volume of 3.42 cu ft, and a spin speed of 440 G at 1200 RPM, driven by a 0.9 HP variable speed induction motor. Water use per cycle is 11.7 gal, the water factor is 3.8, and the modified energy factor is 2.98. Three cycles are offered, Normal, Perm Press, and Delicate, with three water temperatures.

Electrical service is 120 volt, 60 Hz, single phase, 15 amp, and water pressure is 20 to 120 psi. The front control model weighs 270 lb net and measures 26 7/8 in wide, 44 3/8 in high, and 27 3/4 in deep. The cylinder finish is stainless steel, the door is a window door, colors are white or stainless steel, and the front control unit is listed as ADA compliant. The maker lists a three year warranty, parts only.

What stands out:

  • 440 G extraction at 1200 RPM
  • Lowest water use here at 11.7 gal per cycle
  • Front control model listed as ADA compliant

What to watch:

  • Only three wash cycles
  • Three year warranty covers parts only

Buy it if the store wants a compact front loader with a top spin and low water use. Skip it if the store needs a bigger drum.

Buying guide for coin operated laundromat washers

Buying a row of washers is a floor plan decision as much as a machine decision. Capacity, extraction, water, drain, power, payment, and service access all interact, so work through them in order before ordering, and confirm every figure on the maker spec sheet for the exact model.

Match capacity to the loads customers bring

Most laundromat customers bring everyday family loads that fit a 20 lb or 21 lb drum, while bedding, towels, and wash and fold work need a 30 lb or 35 lb machine. A store that stocks only one size will turn away the other kind of load, so a mix across the row usually serves more customers than a single size repeated.

Door opening size matters too, since a wide door makes bulky items easy to load. The Dexter T-400 lists a 15 1/4 in opening and the Wascomat WED730-CV lists a 14 3/8 in opening.

Compare extraction force and drying time

Extraction force, stated in G, decides how much water stays in the load when the wash ends. The 100 G models in this guide leave more water than the 200 G Wascomat, which leaves more than the 327 G LG Titan C and the 440 G Speed Queen and Huebsch front loaders. Less water in the load means a shorter dryer run, which frees dryer pockets faster.

A higher spin is not free, since it needs a stiffer mount and a stronger floor. Favor the higher spin where dryer queues are the bottleneck.

Plan water, drain, and electrical service

Water use per cycle varies widely across the models in this guide, from 11.7 gal for the Huebsch front loader to 40.7 gal for a full load warm cycle on the Wascomat WED730-CV. The Speed Queen FV6 lists 13.68 gal, the Dexter T-300 lists 15.8 gal, and the LG Titan C lists 17.8 gal in between.

Check inlet size, drain diameter, and electrical service on the spec sheet before ordering. The models here list 3/4 in inlets, drain diameters from 2 1/4 in to 3 in, and service from 120 volt 15 amp to 208 to 240 volt.

Choose coin, card, and remote management controls

Coin payment still fits many laundromats, and the models here cover the main options: coin drop on the Speed Queen FV6, a factory dual coin drop on the Maytag, a coin slide on the Huebsch rear control model, and coin acceptors or payment ready on the Dexter C-Series.

Remote management and audit data matter once a store grows past a few machines. DexterLive lets an owner program Dexter washers from off site, and Maytag controls support cycle pricing and audit export through USB.

Plan the floor, spacing, and service access

Hardmount and solid mount washers need a concrete floor, and the Dexter sheets list a minimum concrete thickness of 6 in. The Wascomat sheet states that solid mount machines need a concrete foundation and are not suited to upper floor or above basement installs.

Spacing and access decide how fast a machine returns to service. The Dexter T-300 sheet lists a minimum clearance of 1/2 in between machines and 24 in behind, and notes that the washer fits through a standard 36 in doorway.

FAQ about washers for coin operated laundromats

Owners ask the same questions before ordering a row: what size to buy, how much water a cycle uses, what the floor must hold, and how payment works. The answers below use the figures from the maker pages in this guide, with general install notes where the sheet leaves the detail to the installer.

What size washer works best in a small laundromat?

A 20 lb or 21 lb front loader is the usual starting point for a small store, since it covers everyday family loads in a compact cabinet. The Dexter T-300 at 20 lb, the Speed Queen FV6 at 21 lb, and the Huebsch front loader at 21.5 lb all fit that role, and each runs on a 120 volt 15 amp supply.

Add at least one 30 lb machine if customers bring bedding, since a small drum cannot take those loads well.

How much water does a coin operated washer use per cycle?

It depends on the model and the test cycle the maker used. In this guide the Huebsch front loader lists 11.7 gal per cycle, the Speed Queen FV6 lists 13.68 gal per cycle, the Dexter T-300 lists about 15.8 gal per cycle, and the LG Titan C lists 17.8 gal per cycle.

The Wascomat WED730-CV lists 40.7 gal total on a full load warm cycle, the highest figure here. Compare water figures only between models tested the same way.

Do coin operated washers need a concrete floor?

Hardmount and solid mount washers do, because they transfer spin force into the floor. The Dexter sheets list a minimum concrete thickness of 6 in, and the Wascomat sheet states that solid mount machines need a concrete foundation and are not suited to upper floor installs.

Compact front loaders with their own suspension are more forgiving, but every commercial washer still needs a level, solid floor. Confirm the floor with the installer for the exact model.

Can one washer model take both coins and cards?

Many commercial washers can, with the right control and hardware. The Dexter C-Series line is listed as shipping with coin acceptors or payment system ready, the Maytag lists coin and debit connectors, the LG Titan C is offered in coin, card, and on premise versions, and the Huebsch rear control model offers a coin slide.

Confirm the exact payment setup when ordering, since the coin box, card reader, and related hardware are often separate items.

How often should a laundromat washer be serviced?

Follow the maker manual for the exact model, since service needs vary by build and by how many cycles the store runs. Daily habits help: wipe the door and seal, clear the coin box and payment area, check that the door closes cleanly, and look for leaks at the hoses and drain.

Book a technician for the work the manual reserves for service staff, and keep a log of faults and fixes.

Conclusion

For most small stores, a 21 lb front loader with a 440 G spin is the sound starting point, while a 30 lb 200 G model adds bulk capacity and the 35 lb LG covers the largest loads. Match capacity to the loads, confirm water, drain, and power on the spec sheet, and pick payment controls that fit the customers who walk in.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.