Updated Nov 15, 2026· 14 min read

Key takeaways

  • Five compact kitchen sinks for van conversions compared on stated overall dimensions, bowl depth, minimum cabinet size, drain size and what the maker includes.

A van conversion gives the galley a counter and a cabinet that shares space with a water tank. This roundup compares kitchen sinks for van builds on the figures the makers state: overall dimensions, bowl depth, minimum cabinet size, drain size and included parts, so the sink can be chosen against the cabinet fitted in the van.

Quick verdict

The five picks split by mounting style. Three are undermount sinks that hang below the counter, one is a drop-in bar sink, and one is a full countertop unit with the sink built in. The Kraus is the narrowest at 9-1/2 inches wide, the Ruvati needs the smallest cabinet, and the TORVA replaces the counter surface itself.

Product Type Best for Key spec Main limit
TORVA Countertop w/ 14-inch Sink (Left Side) Countertop with integrated sink Builds with no separate counter 41 x 21.5 inch countertop Counter depth is fixed at 21.5 inches
Kraus KHU101-10 Undermount bar prep Narrow galleys 9-1/2 x 18 inches overall Bowl width is under 10 inches
Elkay BLR15 Drop-in bar sink Thin counters, small drains 15 x 15 inches, 2 inch drain Bowl is 12 x 9-1/4 inches
Ruvati RVH7113 Undermount bar sink 16 inch cabinets 13 x 15 inches, 16 gauge Zero radius corners
Kohler Poise K-3161 Undermount bar sink Deep bowls in small sinks 18 x 18 inches, 9-3/16 inch depth Needs a 21 inch base cabinet

How we selected

Each sink below comes from a manufacturer specification sheet, a manufacturer manual or a listing page that states the overall dimensions in print. Stated dimensions are the first filter for a van, because the galley cabinet is built around tanks, batteries and wheel arches, and its inside width rarely matches a standard kitchen cabinet.

The second filter was mounting style and drain size. Undermount, drop-in and integrated countertop sinks place different demands on the counter panel, and van plumbing often runs smaller waste lines than household plumbing. Every dimension, gauge figure, drain size and included part in this article is copied from the opened page for that model, with nothing carried over from the campervan roundup.

A third filter was what the box includes. Van builds are often finished far from a plumbing supplier, so a sink that arrives with its strainer, clips, template or grid saves a second order. The five sets below differ on exactly that point, and the product sections list the included parts the maker names for each model.

Compact kitchen sinks for van conversions compared

Four of these sinks are bar-size basins between 9-1/2 and 18 inches wide, and the fifth is a 41 inch countertop with a sink formed into it. Bowl depth runs from 7 to 9-3/16 inches, minimum cabinet size from 12 to 21 inches, and drain openings from 1.5 to 3-5/8 inches, so the stated figures separate the picks quickly.

TORVA Stainless Steel Countertop w/ 14-inch Sink (Left Side)

The TORVA unit is a countertop first and a sink second: a 41 by 21.5 inch brushed 304 stainless steel surface with a flush-mounted sink formed into the left side. The listing states it for van conversions and names Sprinter, Transit and Promaster fitments. For a build with no countertop material chosen yet, it covers both jobs in one piece.

The inner sink measures 14.5 by 14.5 inches at 7 inches deep, and the steel thickness is stated as 1.03 millimeters. The faucet hole is 35 millimeters, also stated as 1-3/8 inches. The listing gives a standard 1.5 inch threaded bar sink drain and a drain pipe 31.5 inches long and 1.5 inches in diameter. A sapele wood cutting board sized 14.4 by 14.2 by 0.8 inches is included, and the item weight is 22 pounds.

The stated drain pipe length of 31.5 inches is the planning figure for the waste run: it sets how far the grey water line can travel from the bowl before it needs the builder’s own hose or tank fitting. At 22 pounds for the whole unit, the listing also gives a weight to count against the van payload, which the sink-only models in this group do not state.

  • Pros: counter and sink in one unit, shallow 1.5 inch drain hardware included, cutting board included
  • Cons: counter depth fixed at 21.5 inches, sink sits on the left only, 7 inch bowl depth
  • Buy if: your build has no counter yet and a 41 inch run suits the galley layout
  • Skip if: your counter is already fitted, or you need the sink on the right side

KRAUS Standart PRO 10-in Undermount 16 Gauge Stainless Steel Single Bowl Bar Prep Kitchen Sink – KHU101-10

The KHU101-10 is the narrow sink of the group: the Kraus manual states overall dimensions of 9-1/2 by 18 by 8 inches and a minimum cabinet size of 12 inches. It is an undermount single bowl in 16 gauge stainless steel with a satin finish, and its long, narrow shape suits a galley where the counter depth is spoken for by a cooktop.

The listing states a bowl depth of 8 inches, a rear drain position and a 3.5 inch drain connection, with the drain and strainer included. Kraus names the drain model ST-1 and the drain cap STC-2 in the manual, and gives a corner radius of R3/8 inch. Noise insulation and mounting hardware are listed as included, and the sink is listed as garbage disposal compatible. The stated warranty is a limited lifetime warranty for residential use and a 1-year limited warranty for commercial use.

The rear drain position matters in a cabinet this small: the trap and waste line sit at the back, leaving the front of a 12 inch cabinet usable for a water container or storage boxes. The 12 inch stated minimum is also the smallest cabinet figure in this roundup, which is the reason this model leads for narrow galleys despite its slim bowl.

  • Pros: fits a 12 inch cabinet, 16 gauge steel, drain and strainer included, hardware included
  • Cons: bowl under 10 inches wide limits pan washing, undermount needs a supported counter edge
  • Buy if: the galley cabinet is narrow and you still want a plumbed sink with a standard drain
  • Skip if: you wash wide pans daily, or your counter cannot take an undermount fixing

Elkay Lustertone Classic Stainless Steel 15 x 15 x 7-1/8 inch Single Bowl Drop-in Bar Sink – BLR15

The BLR15 is the drop-in of the group, a 15 by 15 inch bar sink in 18 gauge 304 stainless steel with a Lustrous Satin finish. Elkay states a minimum cabinet size of 18 inches and a cutout of 14-3/8 by 14-3/8 inches. Because it drops in from above and is held by its rim and hardware, it is the simplest mount here for a thin plywood counter.

The bowl measures 12 by 9-1/4 inches at 7 inches deep. The drain is centered and sized at 2 inches, smaller than the 3-1/2 inch openings on the Ruvati and Kraus models, which suits compact waste fittings. Sound treatment is pads on the bottom only. Mounting hardware is included for countertops up to 3/4 inch thick, and the sheet lists ASME A112.19.3 and CSA B45.4 compliance with IAPMO listing.

The centered drain is a planning difference from the rear drain models: the trap sits in the middle of the cabinet rather than at the back. The cutout figure of 14-3/8 by 14-3/8 inches is published on the sheet, so the counter can be marked from the maker drawing before the sink arrives, which suits a build done away from a workshop.

  • Pros: drop-in mount suits thin counters, 2 inch drain suits compact plumbing, hardware included
  • Cons: 18 gauge steel, bottom pads only, bowl is 9-1/4 inches front to back
  • Buy if: you want the simplest install on a plywood counter with a small waste line
  • Skip if: you need a 3-1/2 inch drain or a bowl that takes a dinner plate flat

Ruvati 13 x 15 inch Undermount Bar Sink 16 Gauge Stainless Steel – RVH7113

The RVH7113 is a small undermount in true 16 gauge T304 stainless steel, with an exterior of 13 by 15 inches and a stated minimum cabinet of 16 inches, the second smallest cabinet figure in this group. The maker lists an 18/10 chromium and nickel content and a commercial brushed finish, with zero radius corners for a squared bowl shape.

The bowl measures 11 by 13 inches at 8 inches deep, with a center drain and a 3-1/2 inch drain hole. The maker lists sound guard padding and undercoating, plus a slanted bottom with drain grooves. The box includes a basket strainer, mounting clips, a cut-out template and a rinse grid. The sheet lists cUPC certification by IAPMO. For a van cabinet of 16 inches, this is the pick that keeps 16 gauge steel and a standard drain size.

The included parts are itemized on the sheet: the basket strainer is model RVA1025, the mounting clips are RVA11031 and the rinse grid is RVA67013. Itemized part numbers help in a van build, where a lost grid or a worn strainer has to be replaced by post, and a number is easier to order against than a description.

  • Pros: 16 gauge steel in a 13 inch sink, fits a 16 inch cabinet, rinse grid and strainer included
  • Cons: zero radius corners need more wiping, undermount fixing needs a solid counter edge
  • Buy if: your cabinet is 16 inches and you want the thicker steel and standard drain
  • Skip if: you prefer rounded corners or a drop-in install on a thin counter panel

KOHLER Poise 18-inch undermount single-bowl bar sink – K-3161

The Poise K-3161 is the deep bowl option: an 18 by 18 inch undermount bar sink in premium 16-gauge stainless steel, per the Kohler sheet, with a bowl area of 14 by 14 inches and a bowl depth of 9-3/16 inches. That depth is the most in this group, and it comes with the largest cabinet demand, a minimum base cabinet of 21 inches.

The drain hole is 3-5/8 inches. The sheet lists installation hardware, a bottom sink rack and a bamboo cutting board in the box, plus a template. Kohler prints a lifetime limited warranty section for its stainless steel sinks on the sheet, and lists ASME A112.19.3 and CSA B45.4 compliance, with ADA compliance when the sink is installed per the stated requirements. In a larger van with a 21 inch cabinet, this is the sink that behaves most like a household basin.

The sheet itemizes the included pieces: the bottom sink rack is model K-3142, the bamboo cutting board is K-3140 and the template is numbered 1022021-7. A printed template number matters because the cutout for an 18 inch undermount has to be right the first time; the counter in a finished van is rarely a piece that can be recut cheaply.

  • Pros: deepest bowl here at 9-3/16 inches, rack and cutting board included, 16-gauge steel
  • Cons: needs a 21 inch base cabinet, 18 inch footprint is the largest sink-only model here
  • Buy if: your van has a 21 inch galley cabinet and you wash tall pots and bottles
  • Skip if: cabinet width is under 21 inches, since the maker states that as the minimum

Buying guide

Van galleys punish guesswork: the cabinet is small, the counter is thin and the plumbing shares space with tanks. The checks below follow the order that decides fit in a conversion, starting with the cabinet and the mount, then the drain, then depth and the parts included in the box.

Measure the cabinet, then match the stated minimum

Minimum cabinet size is the maker figure that decides fit, and in this group it runs from 12 inches for the Kraus to 21 inches for the Kohler. Measure the clear inside width of the galley cabinet, allowing for the mounting clips the undermount models use, and compare it with the stated minimum rather than with the sink width.

The Ruvati states 16 inches for a 13 inch sink and the Elkay states 18 inches for a 15 inch sink, so the gap between sink width and cabinet minimum is 3 inches in both cases. That gap is the room the hardware and the bowl walls take up, and it is why a tape measure on the old sink is not enough.

Pick the mount for the counter you have

The Elkay BLR15 drops into a cutout and is held from above, with hardware the maker rates for countertops up to 3/4 inch thick. The Kraus, Ruvati and Kohler models mount under the counter, which needs a counter edge strong enough to carry the sink and its contents on clips. The TORVA removes the question by supplying the counter itself.

Undermount sinks also change how the counter is cut and finished, since the cut edge stays visible. In a van built with a plywood or laminate worktop, the drop-in and the integrated countertop keep the raw edge covered, which is a practical point in a cabin that sees condensation and spills.

The TORVA sink is flush-mounted in its countertop, per the listing, so there is no rim joint standing above the surface and no separate rim seal to renew as the van ages.

Drain size decides the plumbing work

Stated drain openings here run from 1.5 inches on the TORVA drain assembly and 2 inches on the Elkay, to 3-1/2 inches on the Kraus and Ruvati and 3-5/8 inches on the Kohler. The larger openings take standard basket strainers and household traps; the smaller ones suit the compact hose runs used in many van builds.

The Kraus and Ruvati models include a strainer in the box, and the TORVA listing includes the drain pipe at 31.5 inches long. Where a maker does not state a trap or hose size, plan the waste run from the stated opening and the parts supplied, and keep the run short, since van tanks often sit directly below the galley.

Bowl depth against what sits below

Bowl depth runs from 7 inches on the Elkay and the TORVA sink to 9-3/16 inches on the Kohler. A deeper bowl holds a tall bottle upright and keeps splashes in, but it hangs further into the cabinet, where a fresh water tank or a heater often sits in a conversion. The stated depth plus the strainer below it is the vertical space to check.

Depth also trades against width in this size class. The narrow Kraus keeps an 8 inch depth in a 9-1/2 inch width, while the wider Elkay bowl is 7 inches deep. Neither figure is a fault; the choice depends on whether the galley work is drinks and rinsing or full dish washing for a crew.

Gauge and included parts

Three of the five models state 16 gauge steel: the Kraus, the Ruvati and the Kohler. The Elkay states 18 gauge, and the TORVA states a steel thickness of 1.03 millimeters instead of a gauge. A lower gauge number is thicker steel. In a moving vehicle, where items shift in the bowl during travel, the stated thickness is worth weighing.

Included parts differ just as much. The Kohler box includes a bottom sink rack and a bamboo cutting board, the Ruvati box includes a rinse grid and a basket strainer, the Kraus includes its drain and strainer, and the TORVA includes a sapele wood cutting board and the drain pipe. Price the missing pieces before comparing totals.

FAQ

Van sink questions usually come down to cabinet width, drain size and mounting on thin counters. The answers below rest on the figures the makers state for the five models above, and on general fitting practice for small galley cabinets in converted vans.

What size kitchen sinks for van builds fit a 16 inch cabinet?

Two models state minimums at or under 16 inches: the Kraus KHU101-10 at 12 inches and the Ruvati RVH7113 at 16 inches. The Elkay BLR15 states 18 inches and the Kohler K-3161 states 21 inches, so neither fits a 16 inch cabinet on the maker figures. The TORVA is a countertop unit, so its fit turns on counter size, not a cabinet minimum.

Can an undermount sink work in a van counter?

Three picks are undermount models, and each lists mounting hardware or clips in the box. The counter has to carry the sink from its edge, so a solid worktop is needed; a thin panel is a poor match. Where the counter is thin plywood, the drop-in Elkay, whose hardware is rated for countertops up to 3/4 inch thick, is the simpler fixing.

Do kitchen sinks for van galleys use smaller drains?

Some do. The TORVA listing states a 1.5 inch threaded bar sink drain with a matching pipe, and the Elkay states a 2 inch drain, while the Kraus, Ruvati and Kohler models state openings of 3-1/2 to 3-5/8 inches that take standard strainers. The stated opening on the model page is the figure to match to the waste run and tank inlet in the van.

Is an integrated countertop sink a good idea in a van?

The TORVA unit combines a 41 by 21.5 inch countertop with a 14.5 by 14.5 inch sink, a cutting board and the drain pipe in one purchase, which removes the counter cut and the rim seal. The trade is that the counter depth and the sink position are fixed: the surface is 21.5 inches deep and the sink is on the left side, per the listing.

How deep should a van galley sink be?

The stated depths here run from 7 inches to 9-3/16 inches. A 7 inch bowl is enough for glasses, mugs and rinsing, and leaves more room below for a tank. The 9-3/16 inch Kohler bowl takes tall bottles and bigger pans, at the cost of cabinet height. The makers state depth for each model, so match it against the clear height under the counter.

Does the sink weight matter in a conversion?

Only one listing states a weight: the TORVA countertop unit at 22 pounds, which includes the counter surface itself. The Kraus, Elkay, Ruvati and Kohler pages opened for this roundup do not state a weight, so no weight comparison can be drawn for them. Where payload is tight, that missing figure is a question to put to the maker before ordering.

Conclusion

For most van galleys, the Ruvati RVH7113 is the balanced pick: 16 gauge steel, a standard 3-1/2 inch drain and a stated 16 inch cabinet minimum. Choose the Kraus KHU101-10 for a narrower cabinet, the Elkay BLR15 for a thin counter, and the TORVA when the build needs a counter and a sink in one piece.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.