Updated Nov 17, 2026· 15 min read

Key takeaways

  • Compare six digital audio mixers for a CPU by USB channels, sample rate, multitrack recording and computer control, from compact streaming desks to consoles.

A digital autio mixers for a cpu search usually means one thing: a mixer that works with a computer, either sending audio into recording software or taking its controls from the machine on the desk. This guide compares six models on the parts that decide that job: USB channel counts, sample rates, onboard recording, and computer control.

Quick verdict

The six mixers below split into two camps. Five are USB audio interfaces as well as mixers, sending anything from a stereo stream to sixteen channels into a computer. One, the Soundcraft Ui12, uses the computer as a control surface instead and records nothing over USB. The table compares the computer-facing facts first.

Product Analog inputs USB link to computer Recording Control
Yamaha AG06MK2 2 combo plus stereo line inputs 2-in / 2-out, 24-bit / 192 kHz Stereo stream modes with loopback Hardware panel plus AG Controller software
Rode RODECaster Pro II 4 combo Dual USB-C, up to 16 out on interface 1 Multitrack or stereo to microSD, USB storage or computer 5.5-inch touchscreen, 6 physical faders
Mackie DLZ Creator 4 combo plus stereo line inputs USB-C streaming to Mac or PC Multitrack, 12 channels plus main mix, to SD or USB drive Touchscreen with Easy, Enhanced and Pro modes
Tascam Mixcast 4 4 mic combo 14-in / 2-out USB audio interface Up to 14 tracks direct to SD card 5-inch touchscreen, 8 sound pads
Zoom LiveTrak L-8 6 combo plus 2 TS line 12-in / 4-out USB audio interface 12 tracks to SD card, up to 24-bit / 96 kHz Hardware controls, 7 scene memories
Soundcraft Ui12 4 combo plus 4 XLR mic, RCA line USB media playback only, no USB recording None over USB Web browser on PC, tablet or phone, up to 10 devices

How we selected

Each model below is a digital mixer with a stated computer connection, and each product section is built only from facts printed on a product page opened for this guide: input lists, USB formats, sample rates, recording media, dimensions and weights.

Where a page leaves a figure unstated, the section says so instead of filling the gap, and models that are no longer sold are left out entirely. The keyword pairs a mixer with a CPU, so the deciding specs are the ones a computer sees. A two-channel USB link suits a single voice and a backing track. A multitrack link suits a panel show or a small band, because each microphone lands on its own track in the software. Sample rate and bit depth matter where the software session is set high. Control matters too: some of these mixers are mixed from their own screens, one is mixed from a browser window, and that difference shapes the daily routine more than any single number.

Six digital autio mixers for a cpu, compared

The six sections below follow the same order: who the mixer suits, how it connects to a computer, the sourced specifications, the limits a buyer should know, and plain buy-if and skip-if guidance. Streaming desks come first, then the multitrack recorders, then the browser-controlled stagebox.

Yamaha AG06MK2

The AG06MK2 is the smallest mixer here and the most computer-focused: a six-channel streaming mixer whose USB link runs at up to 192 kHz, with loopback and streaming modes chosen for one-person broadcasts. It suits a desk where one or two microphones, a phone and a computer feed one stereo stream, and where the mixer disappears under a monitor.

The input list covers two microphones properly. Channel 1 is a combo jack with switchable +48 V phantom power, and channel 2 is a combo jack with phantom power and a Hi-Z guitar setting. Two stereo line inputs take a phone and RCA sources, a 3.5 mm four-pole socket connects a smartphone for call-ins, and a headset mini jack shares channel 1, though the page notes the headset input and the channel 1 combo cannot be used at the same time. The USB side is a two-in, two-out interface over USB Type-C, USB Audio Class 2.0, at up to 192 kHz and 24-bit.

Onboard DSP adds compression and EQ, an SPX reverb and an amp simulator, with deeper settings handled in the AG Controller software on Windows, Mac or iOS. Streaming output modes include a dry channel 1-2G feed, an input mix and loopback, and a mix-minus switch keeps a caller’s own voice out of their return feed. The unit measures 152 x 63 x 201 mm, weighs 0.9 kg and draws 5 V DC at 900 mA, so a computer USB port or a small adapter powers it.

Pros: the highest sample rate in this group at 192 kHz; loopback and mix-minus are built for streaming rather than added later; the footprint is the smallest here by a wide margin. Cons: two-in, two-out USB means no multitrack recording of separate microphones; only two microphone inputs; the headset and channel 1 combo inputs cannot run together. Buy if one or two voices, a phone and computer audio are the whole show. Skip if separate tracks for each guest are the plan.

Rode RODECaster Pro II

The RODECaster Pro II is a production console for podcasters and streamers, and its computer connection is the strongest here: two USB-C interfaces, so one computer can record while a second streams. Four combo inputs, nine assignable channels and a 5.5-inch touchscreen run the whole show from one desktop unit.

The four combo inputs accept microphone, line and instrument signals through Revolution Preamps with a gain range of 0 to 76 dB and an equivalent input noise of -131.5 dBV, figures that let quiet dynamic microphones run without an inline booster. Six physical faders and three virtual faders cover the nine channels. USB interface 1 works as a two-in, sixteen-out multichannel device or a two-in, two-out mix-minus connection, and interface 2 adds a second two-in, two-out mix-minus link. Recording runs to microSD, USB storage or the computer, multitrack or stereo.

Processing is per channel: exciter, low-end enhancement, leveller, compressor, noise gate, de-esser, high-pass filter and three-band EQ, shaped through the VoxLab editor. Eight SMART pads hold up to 64 actions across eight banks, firing sounds, voice effects or MIDI commands. A built-in receiver pairs with up to two Rode Series IV transmitters, Bluetooth carries phone audio, and Wi-Fi plus Ethernet support remote guests. The console draws 30 W over USB-C Power Delivery at 15 V and 2 A.

Pros: dual computer connections are unique in this group; sixteen output channels over USB give recording software the most to work with; preamp gain and noise figures are the strongest printed here. Cons: four analog inputs cap the in-room panel size; the second USB interface is stereo only; the unit needs a USB-C PD supply rather than plain bus power. Buy if two computers or a computer plus a call machine share one show. Skip if six or more microphones must plug in at once.

Mackie DLZ Creator

The DLZ Creator is an adaptive digital mixer for podcasting and streaming that changes its own controls to match the user: Easy, Enhanced and Pro modes present the same mixer at three depths. It streams and records over USB-C, and can also record full multitrack audio to an SD card or flash drive with no computer present.

Four combo inputs carry Onyx80 preamps, and the input list adds a 1/4 inch unbalanced stereo jack and a 1/8 inch stereo jack for external devices. AutoMix manages levels for up to four microphones, and the Mix Agent assistant guides setup and gain setting, which shortens the path from unboxing to a balanced panel recording. A Bluetooth 5.0 channel brings a smartphone caller in with mix-minus, so the caller hears the mix without their own voice returning as echo.

The digital figures are fixed and simple: a 48 kHz sample rate, 24-bit conversion and a stated system latency of about 3 ms. SD and USB flash recording capture twelve channels plus the main mix at 24-bit and 48 kHz. Outputs are balanced or unbalanced 1/4 inch main jacks and four stereo headphone jacks, so each guest can have a personal headphone feed. The mixer measures 4.1 x 13.0 x 15.0 inches, weighs 6.1 lb and runs from an 18 V, 1.5 A adapter.

Pros: three control modes let beginners and experienced users share one desk; multitrack recording to card or drive works away from the computer; four headphone outputs suit a four-person table. Cons: the sample rate is fixed at 48 kHz, so high-rate sessions are out; four microphone inputs is the ceiling; the maker page opened for this guide does not state a USB channel count, so that figure needs confirming on the listing before purchase. Buy if guided setup and card recording matter. Skip if the session must run above 48 kHz.

Tascam Mixcast 4

The Mixcast 4 is a podcast station built around four microphone inputs and direct-to-card recording: it captures up to fourteen tracks to an SD card while also working as a fourteen-in, two-out USB audio interface. A five-inch touchscreen runs the mixer, and eight trigger pads fire sounds assigned in the bundled Podcast Editor software.

Each of the four combo microphone inputs has auto-mix support, and microphone gain range is stated at 66.5 dB. Call-ins arrive three ways: Bluetooth, USB or a four-pole TRRS connection, each with mix-minus so guests do not hear themselves back. Four headphone outputs let a full table monitor the show. Recording to SD, SDHC or SDXC cards is in WAV format at 48 kHz and 24-bit, up to fourteen tracks made of twelve input tracks plus the stereo mix.

The USB interface runs over a Type-C connection at USB 2.0 High Speed with USB Audio Class 2.0, presenting fourteen inputs and two outputs to the computer. Balanced TRS line inputs take stereo sources, and a 3.5 mm TRRS headset input adds another way to connect a caller or a headset microphone. The unit measures 375 x 57 x 264 mm excluding protrusions, weighs 2.55 kg and uses a dedicated 12 V AC adapter at up to 12.5 W.

Pros: fourteen tracks to a card is the most onboard recording in this group; fourteen USB inputs give software every source at once; three call-in routes cover most guest setups. Cons: USB return is two channels only, so the computer sends back a stereo feed rather than separate tracks; recording format is fixed at 48 kHz; four microphone inputs cap the panel. Buy if a four-person show must record every track with or without the computer. Skip if the computer must return multitrack audio to the mixer.

Zoom LiveTrak L-8

The LiveTrak L-8 is an eight-channel mixer and recorder for podcasts and music sessions: six combo inputs and two TS line inputs, twelve-track recording to an SD card, and a twelve-in, four-out USB audio interface. It also runs on four AA batteries, so it pairs with a laptop away from mains power.

The six preamps carry +48 V phantom power, a gain range of +10 to +54 dB and an equivalent input noise of -121 dBu. Recording to SD captures twelve tracks at once and plays back ten, in WAV at 44.1, 48 or 96 kHz and 16 or 24-bit. The USB interface mode runs at 44.1 or 48 kHz and 24-bit. Each channel has a three-band EQ with high at 10 kHz, mid at 2.5 kHz and low at 100 Hz, a 75 Hz low cut, and one of eight send effects can be dialled in per channel.

Six assignable sound pads hold thirteen preset sounds, seven scene memories store mixer setups, and a TRRS phone connection with mix-minus brings in callers. Four headphone outputs carry three custom monitor mixes plus the main mix. Power options are four AA batteries, the AD-17 adapter at 5 V and 1 A, or USB bus power, with consumption stated at 5 W. The mixer measures 268 x 74 x 282 mm and weighs 1.56 kg.

Pros: six microphone inputs is the most in this group; battery power suits laptop recording away from a desk; scene memories recall a full setup in one step. Cons: USB interface mode stops at 48 kHz even though card recording reaches 96 kHz; the listing opened for this guide showed the model on backorder, so current availability needs confirming; one send effect is shared rather than per-channel processing. Buy if a small band or panel records to card and computer in equal measure. Skip if every channel needs its own full processing chain.

Soundcraft Ui12

The Ui12 takes the keyword from the other side: the computer does not receive audio from this mixer at all, it controls it. The Ui12 is a twelve-input digital stagebox with its own Wi-Fi router, mixed from a standard web browser on a PC, tablet or phone, with up to ten control devices connected at once and no app to install on any of them.

Inputs total twelve: four combo mic/line jacks, four XLR microphone inputs, two Hi-Z instrument channels and a stereo RCA line input. Every input carries a four-band parametric EQ, high-pass filter, compressor, de-esser and noise gate, and outputs carry a 31-band graphic EQ with dbx AFS2 feedback suppression. Three Lexicon effects processors cover reverb, delay and chorus. Main outputs are XLR and 1/4 inch, aux sends are two balanced XLR, and two 1/4 inch headphone outputs are fitted.

The computer link is control only, and the page is plain about the boundary: USB connectivity is a two-channel media player for playback from USB storage, and USB stereo recording is listed as not available on this model. Ethernet control sits alongside the Wi-Fi for a wired, steadier connection. The stagebox measures 85 x 177 x 320 mm and weighs 2.29 kg, and because there are no faders on the hardware, a working control device is part of the setup, not an accessory.

Pros: any computer with a browser becomes the control surface, across Windows, Mac, Linux, iOS and Android; eight microphone inputs suit a small live rig; snapshot recall stores settings per song or scene. Cons: no audio reaches the computer, so it cannot record a show into software; no physical faders; USB recording is absent by design. Buy if the computer’s job is mixing a live room from anywhere in it. Skip if recording into the computer is the whole point.

Buying guide

A mixer and a computer can work together in three different ways, and the buying decision starts with naming which one the setup needs. The guide below works through the checks in order: USB direction and channel count, sample rate, where recording lives, how guests join, and desk space.

Count the USB channels the software must see

USB figures decide what recording software can do with a mixer, so read them as two numbers: channels into the computer and channels back. A two-in, two-out link like the AG06MK2 sends one stereo mix, which suits a single host. Fourteen-in and twelve-in links like the Mixcast 4 and LiveTrak L-8 send each source separately.

The Ui12 sends none, because its USB socket plays media files instead of streaming audio.

Match the sample rate to the session

Sample rate only matters when the mixer and the software session disagree, but then it matters at once, because the session must be set to a rate the hardware supports. The AG06MK2 reaches 192 kHz, the LiveTrak L-8 records to card at up to 96 kHz while its USB mode runs at 48 kHz, and the DLZ Creator and Mixcast 4 work at 48 kHz.

A podcast recorded at 48 kHz loses nothing by choosing a 48 kHz mixer; a music session tracked at 96 kHz needs the hardware to match.

Decide where the recording lives

Recording to a card inside the mixer and recording into computer software are two different backup paths. Card recording keeps working when the computer sleeps, crashes or stays at home, and the Mixcast 4, LiveTrak L-8 and DLZ Creator all capture multitrack audio that way.

Software recording puts every track straight into the editing session, which the RODECaster Pro II and the USB interface modes here support. Setups that cannot afford a lost take often use both at once.

Plan how remote guests join the mix

Guests who are not in the room need a route into the mixer and a mix-minus feed back, so they hear everyone except themselves. The AG06MK2 takes a phone through its four-pole socket, the Mixcast 4 adds Bluetooth and USB routes, the DLZ Creator uses Bluetooth, and the RODECaster Pro II adds a second computer connection and network calls.

Count the guest routes the show actually uses, then check each one against the input list before choosing.

Check desk space, power and monitoring

Computer desks fill quickly, and these mixers range from the 0.9 kg AG06MK2, powered from a USB-level 5 V supply, to widescreen consoles that need their own adapters. Headphone outputs matter at the same time: one output suits a solo host, while four outputs on the Mixcast 4, LiveTrak L-8 and DLZ Creator let every guest hear a personal feed.

Measure the desk, count the headphones, then pick the frame that fits both.

FAQ

Most questions about pairing a digital mixer with a computer come down to what travels over the USB cable. The answers below stick to the figures printed on the product pages used in this guide, and they point back to the product sections where a model-specific number matters, so nothing here rests on a claim about how mixers behave in general.

Do digital autio mixers for a cpu send every microphone to separate tracks?

Only some of them do, and the USB input count is the tell. The Mixcast 4 presents fourteen inputs to the computer and the LiveTrak L-8 presents twelve, so each microphone can land on its own track. The AG06MK2 presents two, so the computer receives the finished stereo mix.

The Ui12 presents none, because it is controlled by the computer rather than feeding it, which is why the USB figures come first in every section of this guide.

Can these mixers record without a computer?

Four of the six can. The Mixcast 4 records up to fourteen tracks to an SD card, the LiveTrak L-8 records twelve tracks to SD, the DLZ Creator records multitrack audio to SD or a USB drive, and the RODECaster Pro II records to microSD, USB storage or the computer. The AG06MK2 is built to stream through the computer.

The Ui12 has no USB recording at all, so it always works alongside another device when a recording is needed.

What does mix-minus do for a phone guest?

Mix-minus sends a caller the full mix minus their own voice, which stops the echo and delay that make phone guests hard to follow. The AG06MK2 has a mix-minus switch for its phone input, the Mixcast 4 applies it across Bluetooth, USB and TRRS, the DLZ Creator uses it on Bluetooth, and the RODECaster Pro II builds it into both USB interfaces.

Any setup with regular remote guests should treat mix-minus as a requirement, not a bonus.

Is a higher sample rate always better for computer recording?

Not for every job. Speech recorded for podcasts and streams is commonly delivered at 48 kHz, and every mixer here can work at that rate. Higher rates earn their place in music sessions where the software project is set to 96 kHz or above, and only the AG06MK2 at 192 kHz and the LiveTrak L-8 card recording at 96 kHz reach into that range.

The practical rule is to match the mixer to the session rate the work already uses.

Can one mixer serve two computers at once?

Among these six, only the RODECaster Pro II states two computer connections: its dual USB-C interfaces let one machine record while another streams, or keep a call computer separate from the recording computer. The Ui12 takes the opposite route, letting up to ten devices control it while sending audio to none of them.

The other four models here each connect to a single computer at a time over USB.

Conclusion

For a single voice, the AG06MK2 covers the computer link with the least fuss. For multitrack shows, the Mixcast 4, LiveTrak L-8 and DLZ Creator record every source to card and computer alike, and the RODECaster Pro II adds a second computer connection. The Ui12 stands apart for browser control. Match the USB count to the session first.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.